A-803i Amplifier for Subwoofer and Bass Shaker

From €299.00 *
Content: 1 Stück
Artikelnummer: A-803i
Versandgewicht: 8.5 kg

Prices incl. VAT Depending on the delivery address, the VAT may vary at the checkout.plus shipping costs

Optional with BS-200i

Product information "A-803i Amplifier for Subwoofer and Bass Shaker"
The enormous power reserve of up to 1000 watts not only powers large, heavy, long-throw subwoofers. The amplifier is also sufficient for several low bass transducers (bass shakers up to 6) for installation in seating furniture, cinema chairs and playseats.
The successor to our 1000-times proven powerhouse A-802 has the same technology and differs in the mono RCA socket, which connects to the AVR / surround receiver mono subwoofer output, and the new automatic fuse on the back. An RCA adapter is included for duplicating individual AVR subwoofer outputs.
Due to the very large transformer with the analogue, efficient power supply, the output of 1 x 800 W / 2 Ohm remains stable in the low bass. The power amplifier is digital with high efficiency and low heat development.
The front panel controls are sufficient for all bass shaker settings and most subwoofers.
For extremely precise adjustment and room matching, the A-803i amplifier can be combined with the DSP-6mini digital crossover.
You will find further important information in the taskbar under the product pictures.

connection to AV receivers

LEVEL SUB controls the input sensitivity / volume. The SUBWOOFER output of the AV receiver or other music sources should be set to approx. + 80% to send a strong, clean signal to the A-802 INPUT L or R or both (for stereo subwoofer outputs).
SUB OUT - HIGH CUT limits the frequencies above 40 - 300 Hz. For structure-borne transducers we recommend 50-70 Hz = control position 8-10:00 for movies. For games / car racing you can set to 10-12:00.
SUBSONIC: For music with a lot of low bass, turn slowly from the very left to the right until the low bass or the vibration of the structure-borne sound transducer becomes slightly weaker, then again 3-4mm to the left = reactive power is filtered = more useful reserve.
If you turn the subsonic control further to the right, you can mechanically and electrically relieve small subwoofers.
A manual or automatic boost with measuring systems of the falling low bass is not necessary, without additional 5-fold amplifier reserve. The lowest octave of 20-40 Hz requires more than 70% of the total power. In this range it is not a question of subtleties, but of sheer power = fast, strong current delivery for impulse fidelity in low bass even at very high power levels.
If only one subwoofer RCA output is available on the AV receiver, this can be doubled with the enclosed Y-adapter. A Cinch mono cable then leads to the amplifier INPUT L or R.
Power for up to 6 x BS-200i:
For large seating areas with 2 separable elements you need 2 x BS-200i per element. The high power reserve of the A-803i enables strong and precise vibrations, as well as 4-6 separate armchairs or a platform up to 500 kg total weight with persons.

BS-200i Connection variants

An odd number of shakers is very unfavourable.
Examples:
3 x 4 ohms in series = 12 ohms = low amplifier power.
3 x 4 ohms in parallel = approx. 1.3 ohms = too low - even for our 2 ohm capable amplifiers.

2 x BS-200i solid-borne sound transducers with the subwoofer amplifiers A-800 bis A-803i
The terminals of the BS-200i are large enough to connect to the first terminal when two 4 mm² speaker cables are connected in parallel and further to the second with two 1.5mm² to 3m speaker cables. Two BS-200i with 4 Ohm each (that's 2 Ohm amplifier load) are fine for the amplifier or other 2 Ohm capable power amplifiers. For each two BS-200i one above mentioned amplifier is needed, because at higher total impedance than 2 Ohm the power decreases, which is then distributed to the shakers (too little power per shaker).
Parallel connection Series connection
Anschlußvariante für den BS-200i Reihenschaltung = 8 Ohm stabiler gegen Überlast
1. the amplifier power is highest with parallel connection = 2 ohms. If this is not needed, the series connection = 8 Ohm is more stable against overload.
2. 2 x BS-200i share the "work" more confidently than if you get all the vibration from just one unit.
3. if you have separate seats, you need one unit per seat anyway. Platforms are also better driven by 2 x BS-200i in different places.
4. the load capacity is doubled and the voice coils do not get so hot.
5. the vibrations reach deeper, but the impulse fidelity and tight reproduction are maintained.
The BS-200i belongs to the tightly tuned solid-borne sound transducers without the disadvantages of the constructions mentioned below:
A. Softer magnet suspension / lower resonance frequency = less restoring force = spongy reproduction.
B. Greater weight of the vibrating parts = longer reverberation = delayed reproduction.
C. Longer voice coil for more stroke = even longer reverberation.
amplifier setting:
It is particularly useful to use the variable SUBSONIC. Turn from the far left to the right until the vibration becomes slightly weaker, then turn again 3-4mm to the left. This filters the ineffective frequency range = the reactive power. This reduces the load on the solid-borne sound transducers and amplifiers, so that even more power is now available for the useful range. This function is especially important when the lower bass range for the subwoofers is being pushed by calibration systems. Furthermore, the BS-200i reacts only slightly to changes in frequency response and filtering of room modes.
PHASE is used to optimise the cooperation between the solid-borne transducer and the airborne woofer. To do this, run both up to approx. 150 Hz and turn PHASE until it has the loudest / strongest effect = both run in phase. Then limit to the desired highest frequencies. We recommend 50-70 Hz = HIGH CUT approx. 9 o'clock to 9:30, but for games and car races you can run the BS-200i up to 150 Hz = HIGH CUT approx. 11 o'clock to 13:00.
Interaction with subwoofers:
For subwoofers (airborne sound) and shakers (structure-borne sound) you need separate amplifiers to match them; because the structure-borne sound transducers need 5-10 times the power to complement the airborne sound optimally. Since most subwoofers have built-in power amplifiers, you only need one mono amplifier for the shakers. However, these must have a particularly strong power supply like the Reckhorn amplifiers in order not to drop off in the low bass like almost all simply built amplifiers.
Audio Video / Main Unit Setting:
SUBWOOFER OUTPUT / SUB OUT / LFE should be turned up about plus 80% to send a strong signal to the subwoofer amplifier via mono RCA cable. This is even more important if you have to double the output with Y-Cinchadaptor to make one = two outputs = 1 x to the normal subwoofer + 1 x to the amplifier for the BS-200i bass shakers. Also with 2 x SUB OUT cinch sockets you should turn up + 80% so that you can turn down the input sensitivity of the following subwoofer amplifiers = less risk of interference. In this case, the volume relation subwoofer - bodysound transducer can be adjusted more comfortably via the remote control.

Video

Präsentationsvideo des Subwoofer-Mono-Verstärker aus der Sicht des Entwicklers,
A-409, A-800 & 803i durch Herrn Klaus Reck persönlich.

Zubehör

G-44-14 Rubber Bumpers G-44-14 Rubber Bumpers
Content 1 Quadratmeter
€0.50 *
Speaker cable L-4 / per meter Speaker cable L-4 / per meter
Content 1 Laufende(r) Meter
€2.95 *
Bananastecker für Kabel von 1,5 bis 6mm² Rot Banana plugs
From €0.79 *
Cinchkabel 1 Meter L (left) with high quality for home and car Hifi Cinchkabel 1 Meter L (left) with high quality...
Content 1 Laufende(r) Meter
€1.99 *
Cinchkabel 1 Meter R (right) with high quality for home and car Hifi Cinchkabel 1 Meter R (right) with high quality...
Content 1 Laufende(r) Meter
€1.99 *
L-1,5-10 speaker cable 2 x 1,5mm², 10 meters L-1,5-10 speaker cable 2 x 1,5mm², 10 meters
Content 10 Laufende(r) Meter (€0.70 * / 1 Laufende(r) Meter)
€6.95 *
Bass-Body / Shaker / Transducer Bass-Body / Shaker / Transducer
Content 1 Stück
€49.00 *
Cinchkabel 5 meters L (left) with high quality for home and car Hifi Cinchkabel 5 meters L (left) with high quality...
Content 5 Laufende(r) Meter (€0.72 * / 1 Laufende(r) Meter)
€3.59 *
Cinchkabel 5 Meter R (right) with high quality for home and car Hifi Cinchkabel 5 Meter R (right) with high quality...
Content 5 Laufende(r) Meter (€0.72 * / 1 Laufende(r) Meter)
€3.59 *
Kleber-Kartusche für Schallabsorber AS-600 Montagekleber für Schallabsorber Dämmplatten
Content 300 ml (€0.43 * / 100 ml)
€1.29 *
D-165 Subwoofer Built-in Speaker D-165i Subwoofer Built-in loudspeaker
Content 1 Stück
€34.99 *
P-6.5 Passive radiator 16 cm / 6.5 " P-6.5 Passive radiator 16 cm / 6.5 "
Content 1 Stück
€14.95 *
1 X S-150 Kugellautsprecher S-150 spherical full range Speaker 1 piece
Content 1 Stück
From €22.95 *
Hint!
D-200 Subwoofer Bass Lautsprecher Anschlüsse D-200 Subwoofer Built-in loudspeaker
Content 1 Stück
€49.00 *
S-300 Satelliten Speaker 1 piece S-300 Satelliten Speaker 1 piece
Content 1 Stück
€99.00 *
Flex-3 eine Rolle mir 15 Meter Gummischaumband selbstklebend Gummischaumband selbstklebend
Content 15 Laufende(r) Meter (€0.33 * / 1 Laufende(r) Meter)
€4.99 *
W-132 13cm Tiefmitteltonlautsprecher W-132 13cm low-mid speaker
Content 1 Stück
€24.99 *
Speaker cable L3 / per meter Speaker cable L3 / per meter
Content 1 Laufende(r) Meter
€2.95 *
Hint!
S-300 Satelliten Speaker 1 piece S-300 Satelliten Speaker 1 piece
Content 1 Stück
€149.00 *
Screw Terminal Screw Terminal
Content 10 Stück (€0.99 * / 1 Stück)
€9.90 *
Hint!
ABX 2 mm Alubutyl Sound insulation & deadening material ABX 2 mm Alubutyl Sound insulation & deadening...
Content 2 Quadratmeter (€15.00 * / 1 Quadratmeter)
From €29.99 *
Bass-Body / Shaker / Transducer Bass-Body / Shaker / Transducer
Content 1 Stück
€49.00 *
G-44-14 Rubber Bumpers G-44-14 Rubber Bumpers
Content 1 Quadratmeter
€0.50 *
Hint!
Speaker cable L3 / per meter Speaker cable L3 / per meter
Content 1 Laufende(r) Meter
€2.95 *
Hint!
S-300 Satelliten Speaker 1 piece S-300 Satelliten Speaker 1 piece
Content 1 Stück
€149.00 *
Bananastecker für Kabel von 1,5 bis 6mm² Rot Banana plugs
From €0.79 *
D-165 Subwoofer Built-in Speaker D-165i Subwoofer Built-in loudspeaker
Content 1 Stück
€34.99 *
S-300 Satelliten Speaker 1 piece S-300 Satelliten Speaker 1 piece
Content 1 Stück
€79.00 *
Hint!
D-200 Subwoofer Bass Lautsprecher Anschlüsse D-200 Subwoofer Built-in loudspeaker
Content 1 Stück
€49.00 *
S-300 Satelliten Speaker 1 piece S-300 Satelliten Speaker 1 piece
Content 1 Stück
€99.00 *
Hint!
Hint!
Speaker cable L3 / 60 meter Speaker cable L3 / 60 meter
Content 60 Laufende(r) Meter (€2.48 * / 1 Laufende(r) Meter)
€149.00 *
DSP-6 mini crossover adaptor DSP-6 mini crossover adaptor
Content 1 Stück
€9.95 *
Speaker cable L-4 / per meter Speaker cable L-4 / per meter
Content 1 Laufende(r) Meter
€2.95 *
Hint!
ISO-20.12 Geräuschdämmung + Wärme-Kälteisolation für Caravan und Wohnmobile The ISO-20 / 12 insulation panels for...
Content 6 Quadratmeter (€14.99 * / 1 Quadratmeter)
€89.95 *
W-132 13cm Tiefmitteltonlautsprecher W-132 13cm low-mid speaker
Content 1 Stück
€24.99 *
P-6.5 Passive radiator 16 cm / 6.5 " P-6.5 Passive radiator 16 cm / 6.5 "
Content 1 Stück
€14.95 *
Cinchkabel 1 Meter R (right) with high quality for home and car Hifi Cinchkabel 1 Meter R (right) with high quality...
Content 1 Laufende(r) Meter
€1.99 *
T-1.0F Kalottenhochtöner T-1.0 dome tweeter
Content 1 Stück
€9.99 *
Cinchkabel 1 Meter L (left) with high quality for home and car Hifi Cinchkabel 1 Meter L (left) with high quality...
Content 1 Laufende(r) Meter
€1.99 *
1 X S-150 Kugellautsprecher S-150 spherical full range Speaker 1 piece
Content 1 Stück
From €22.95 *
F-6.5 Bassmitteltöner Einbaulautsprecher F-6.5 bass-mid speaker / one piece
Content 1 Stück
€19.95 *
Hint!
ISO-20 Geräuschdämmung + Wärme-Kälteisolation für Caravan und Wohnmobile The ISO-20 / 6 insulation panels for insulating...
Content 3 Quadratmeter (€15.65 * / 1 Quadratmeter)
€46.95 *
Hint!
L-1,5-10 speaker cable 2 x 1,5mm², 10 meters L-1,5-10 speaker cable 2 x 1,5mm², 10 meters
Content 10 Laufende(r) Meter (€0.70 * / 1 Laufende(r) Meter)
€6.95 *
Hint!
DV-10 dampening nonwoven DV-10 dampening nonwoven
Content 2.4 Quadratmeter (€11.25 * / 1 Quadratmeter)
€26.99 *
BT-2 Desktop Bluetooth Speaker BT-2 Desktop Bluetooth Speaker
Content 1 Stück
€19.95 *
Screw Terminal Screw Terminal
Content 10 Stück (€0.99 * / 1 Stück)
€9.90 *
Flex-19 Wärme & Kälte Dämmung Matten für KFZ / Wohnwagen / Camper bemaßt Heat & cold insulation in the car / caravan /...
Content 6 Stück (€5.99 * / 1 Stück)
€35.94 *

FAQ

Additional information: "A-803i Amplifier for Subwoofer and Bass Shaker"

Evaluations

Write an evaluation
Evaluations will be activated after verification.
Please enter these characters in the following text field.

The fields marked with * are required.

I have read the data protection information.

Customer evaluation for "A-803i Amplifier for Subwoofer and Bass Shaker"
10 Aug 2021

Einwandfrei

Herausragende Firma!
Absolut auf Zack.
Nachfragen wurden schnell und unmissverständlich geklärt.
Die von mir im "Playseat" verbauten BS 200i machen richtig Spaß.
Ein neues Gamingerlebnis! Von "Jurassic World Evolution" bis "Formel1 2021"

10 Jun 2021

A-803 i = Tolles Gerät !

Ich habe mir den A-803i zugelegt, um meinen defekten Bowers & Wilkins PV1 wieder zu beleben.
Nachdem ich die beiden Basstreiber parallel geschaltet habe und alles weitere so umgebaut wurde das ich es anschließen konnte, traute ich meinen Ohren nicht. Volltreffer!!!!
Reanimation gelungen. Kraftvolle und satte Bässe.
Der einzige Wermutstropfen ist, das dieses Gerät nicht über einen „Standby“ Modus verfügt (obwohl an dem Verstärker eine Kontrolllampe vorhanden ist) und das Gerät immer an und aus geschaltet werden muss.
Vielleicht solltet ihr einen Nachrüstsatz anbieten, zumindest für ferngesteuerte an/aus Befehle.
Ansonsten eine Superschnelle Lieferung und gute Verpackung !
Liebe Grüße aus dem Ruhrpott.

7 Apr 2021

A 802 - Super Verstärker, super Service

Hallo zusammen,
als erstes ein ganz grosses Dankeschön an Herrn Reck und Herrn Nachtigall. Euer Service und Eure Kompetenz gepaart mit der Geuld mir alles zu erklären war phantastisch. Ich hatte schon zwei BS200 im Betrieb und wunderte mich, dass es zu wenig "wackelt" und mehr brummelt. Mein Sofa ist einfach zu schwer. Daher war die Empfehlung 2 weitere BS200 Shaker drunterzuschrauben. Den Antrieb der 4 Shaker übernimmt nun der A 802, den man sehr komfortabel über die Front bedienen kann. Das Brummen ergab sich aus der Eigenfrequenz des Sofas, bzw der Armlehnen, die hohl waren und mitgeschwungen sind. Armlehnen sind nun weg und es passt alles. Wenn jetzt die A10 Thunderbolt von den Hunterkillern in Terminator 4 verfolgt werden, dann wirds spassig. DAS ROCKT. Trotzdem kann ich nur jedem empfehlen den Subwoofer trotzdem mitlaufen zu lassen. Dann stellt sich ein herrliches Kinoerlebnis ein. Genau das richtige, wenn man nicht mehr ins Kino kann, wie zur Zeit gerade.
Ich hab aber noch zwei Verbesserungsvorschläge: das ganze fernbedienbar und die Montageschrauben könnten etwas robuster sein. Sonst reissen die Senk-Köpfe schnell ab. ;-) .
Für nächsten Winter liebäugle ich schon mit dem DSP 6 mini, um das Shaken noch weiter finezutunen und zu kontrollieren. Liebes Reckhorn-Team, weiter so, bei Euch wird man gut beraten, ohne Vodoo.... :-)
Freundliche Grüße
D. Patwardhan

1 Apr 2021

Für mich die ideale Lösung um aus einem defekten aktiven Sub einen heilen passiven Sub zu machen

Einwandfreies Gerät ohne Störgeräusche mit einem recht geringen Energieverbrauch und ausreichender Leistung.

16 Mar 2021

Lieferung

Also, muß erstmal loben, sehr schnelle Lieferung und sehr gut verpackt, jetzt muß ich den 803i erstmal warm werden lassen so das er auf Zimmerthemperatur kommt. Er ist super kalt, ich glaube er lag im Gefrierfach. Nun fange ich in Ruhe an diese Bass Shaker zu installieren.

22 Jan 2021

Sinnvolles Zusatzgerät für den Einsatz und die Steuerung von Bass Shakern

Ich habe mir den Reckhorn A-830i gekauft, um damit 4 Reckhorn Bass Shaker BS 200-i in einem 5.1.2 System zu betreiben.
Bisher wurde testweise ein Shaker parallel zu einem regelbaren KEF Sub, über die zweite Zone eines Denon AVC X4700H betrieben. Das hat zwar grundsätzlich funktioniert, brachte aber auch Nachteile mit sich bringt.
Die Leistung der Endstufen des AVC sind zu gering, so dass bei hohem Pegel auf dem Shaker gerne mal die Sicherung den Verstärker abgeschaltet hat. Dazu kommt, dass sich das LFE Signal aus dem Subout des AVC nicht getrennt regeln ließ und der 2. Subout Ausgang unter Audyssee nicht berücksichtig wird, wenn kein zweiter Subwoofer angeschlossen ist.
Somit werden Highcut und Pegel beim Einmessen über Audyssee nur für den angeschlossen Subwoofer berücksichtigt. Der per Y-Kabel parallel angeschlossene Shaker läuft nun mit diesen Werten mit, was u.U. aber gar nicht gewünscht ist, da ja nur die wirklich tiefen Frequenzen > 60 hz den Shaker in Gang bringen sollen.
Hier kommt nun der sauber und schnörkellos verarbeitete Reckhorn A-830i mit riesigem Ringkerntrafo zum Einsatz. Seine 800 Watt bieten genug Reserven. Pegel, Frequenz und Sub Sonic Filter lassen sich für die Shaker getrennt vom Subwoofer einstellen und sorgen damit für ein völlig neues Hör/Fühlerlebnis.
Ich möchte noch erwähnen, dass meine Fragen die ich hatte, sofort und kompetent von Herrn Reck persönlich beantwortet wurden.
Mein Fazit daher: Preis -Leistung-Service top und daher "Sehr empfehlenswert" !!!

10 Jan 2021

Druckvoller, kontrollierter Klang

Der Reckhorn A 803i befeuert einen Dayton Audio RSS315 HFA 8, 12" Subwoofer mit 8 Ohm Inpedanz in einem geschlossenen 62l Gehäuse. Die Leistung des Reckhorn reicht auch an 8 Ohm aus, um den Dayton mühelos im ganzen Frequenzbereich zu betreiben. Daher mache ich mir keine Sorgen, dass er auch einen zweiten Dayton in Parallelschaltung sauber betreiben kann.
Das Gerät ist kompakt, recht leise und die Anschlussklemmen halten die Kabel stabil.
Für den Preis gibt es auch im PA Bereich keine bessere Endstufe für Subwoofer.

Viewed
Kaufberater.io TOP-SHOP 2019: Reckhorn Audio GmbH
ExpertenTesten kürt die besten Webshops 2019: RECKHORN
Reckhorn Audio GmbH - Platz 1 im Einzelhandel in Kaltenkirchen, Schleswig-Holstein
Händlerbund Käufersiegel